Hematite Iron Ore Processing Plant

Hematite Iron Ore Processing Plant

The main equipments commonly included in Hematite Iron Ore Processing Plants include Hematite Iron Ore Processing mill main engine, vibrating feeder, bucket elevator, belt conveyor, powder sorting equipment, dust collector equipment, screening equipment, powder sorting equipment and powder collector. Wait. Among them, belt conveyors, vibrating feeders and bucket elevators are often referred to as auxiliary equipment for the production line. As a whole, the production line, even for auxiliary equipment, we can not be careless, we must carry out regular maintenance and preventive measures to prevent damage in the production process, resulting in production failure. Among them, the belt conveyor is more used, and it is used in various parts. For example, the material conveying and the conveying of finished materials will use the belt conveying equipment. Here we take the belt conveyor as an example to introduce the second. The causes and precautions of the auxiliary equipment of the Hematite Iron Ore Processing Plant, and what effective methods are usually used to extend the service life of the auxiliary equipment.

Wear causes and preventive measures of Hematite Iron Ore Processing Plant assisting equipment

In general, the cost of a belt conveyor in a Hematite Iron Ore Processing Plant is 30%-50% of the total cost. Therefore, in the design of the belt conveyor, corresponding measures are taken to reduce the wear of the conveyor belt and to extend the life of the conveyor belt. This has a very practical significance for the normal operation of the belt conveyor used in the Hematite Iron Ore Processing Plant, and the maintenance cost is greatly reduced. I will detail the causes of wear and preventive measures. I hope it will help you!

The normal service life of a belt conveyor in a Hematite Iron Ore Processing Plant depends on the wear of the belt conveyor. Most of the belt conveyor damage is caused by work surface wear and edge wear. The former is mainly caused by the relative sliding of the conveyor belt and the material conveyance. The material before the grinding has sharp edges and corners, and there will be a large cut or scratch on the surface of the belt. If the scratching situation is serious, the user is Failure to deal with it in a timely manner will cause problems in this place where the abrasion will occur soon. After comparison, the entire belt conveyor needs to be replaced. The finished material after grinding by Hematite Iron Ore Processing mill is usually thin and will not cause too much influence on the surface of the belt conveyor, but these fine particles will be drilled into the bearing of the belt conveyor, polluting the lubricating oil, so that It can also cause the belt conveyor to malfunction. Of course, these fines can also cause friction with the components of the conveyor, causing severe wear on the components of the conveyor.

The edge wear of the conveyor belt of the Hematite Iron Ore Processing Plant is mainly caused by the wear and friction of the belt edge and the frame under the deviation of the conveyor belt. During the operation, when the equipment is seriously deviated for a long time, it is easy to cause the conveyor belt to tear, and the rubber covers partial peeling and scratching, and the load of the belt conveyor is increased, resulting in low production efficiency. If this phenomenon occurs in the belt conveyor at the inlet, the feeding will be too slow, causing the Hematite Iron Ore Processing mill to idling, wasting energy, and resulting in inefficient production. If this phenomenon occurs in the discharge port, it will cause the equipment to discharge too slowly, causing blockage, which will seriously affect the fine powder operation of the Hematite Iron Ore Processing mill .

Users and professional maintenance personnel need to analyze the cause of wear on the conveyor belt. When designing the conveyor belt, appropriate precautions can be taken to extend the life of the conveyor belt. First, we must reasonably choose the conveyor belt. The selection of the Hematite Iron Ore Processing Plant belt conveyor requires consideration of many factors, both the production capacity of the Hematite Iron Ore Processing mill and the physical properties of the material to be processed. When choosing the model and type, you need to refer to the following two factors. For example, the choice of belts should focus on the following three aspects: the shape and structure of the conveyor belt, the core material, the choice of structure, and the choice of the cover layer.

Second, reduce the wear on the conveyor parts on the conveyor belt. Conveyor components are basically standard equipment, we should choose a professional belt conveyor manufacturer. Consumables that are prone to wear on the belt should be adjusted to reduce wear during installation and to pay attention to inspections. Then, the structure of the Hematite Iron Ore Processing mill feeding device should be optimized. The task of the feeder is to ensure that it loads the material transported on the belt conveyor. It is worth noting that the service life of the Hematite Iron Ore Processing Plant using the conveyor belt is largely related to the structure of the feeding device.